Panel type catalog, prestressed hollow core element

Module(s): Catalogs

'General' tab

Created on:

Date of creation of the data record.

Last modified:

The most recent modification date.

Name:

You can enter any name. This name is displayed in the Type list box of the basic parameters for slab element design if the Description box is empty. This way, you can enter a short name for the catalog and a detailed description for the design.

Description:

You can enter any name. This name is displayed in the Type list box of the basic parameters for slab element design.

Panel thickness:

The standard value for panel thickness.

Max. panel length:

Maximum value for the panel length. If this value is exceeded during the design process, the program will issue a message.

Longitudinal section:

Selection box of the joint section catalog. These sections are used for element design and cannot be modified. All the edges to which you assign the longitudinal section are given the Smooth edge or Stop position attribute.
To assign this attribute to a panel edge without profiling, you need to define a "smooth" section in the joint section catalog and assign it here.

You can define how sections are displayed and labeled in the configurations.

Standard panel width:

Default value for the panel width. This value is used for uncut panels in element design.

Min. fitted panel width:

Minimum value for the panel width. If this value cannot be complied with, the program will create a strip made of in-situ concrete or two fitted panels (depending on your settings).

Max. fitted panel width:

Maximal value for the width of a cut panel. If this value is exceeded, two fitted panels are created.

Min. offset from cut to web at start/end:

Minimum value for the left/right offset from cuts in areas of hollow blocks to the web. The program determines the widths of fitted panels and positions of openings based on this entry.

Opt for cut in axis:

When generating fitted panels, the program attempts to cut the panels in the area of the hollow block axis and to use permissible values for the support widths. If the result is an illegal panel, the minimum offsets from the cuts to the webs are used.

Dead weight:

Weight of panel including hollow blocks in [to/m2]. The program uses this value to calculate the weight based on the length and width of the panel.

'Recesses 1' tab

Recesses that are larger than the ones defined here can be created using steel headers. The recess width is also used to define the number of webs that are cut.

Small recess between two webs:

Maximum length of recesses which are not wider than the space available between two webs.

Medium-sized recesses:

Minimum edge offsets for recesses which are wider than small recesses; however, these recesses do not exceed the limits defined in the Recesses 1 and Recesses 2 tabs.

By defining these minimum offset values, you can prevent non-producible or failure-prone panel webs from being generated as the program extends the recesses to the panel edge. However, these offsets are only used if medium-sized recesses cannot be moved.
This way, recesses at room edges, which result in narrow webs (due to the support) are not treated as lateral or centered recesses. Rather, they retain their positions.

In addition, these minimum offset values can be used to change recesses in midspan into support recesses in the head region or into lateral recesses and vice versa.

Support recess in corner / head region:

Maximum dimensions for recesses as shown below.

If a displacement is not allowed and if, in the case of recesses in the head region, the edge offset to the longitudinal side is smaller than the minimum offset specified for medium-sized recesses, the program will create a recess in the corner.

Note: The two options displayed cannot be created in one and the same panel!

Projecting panels in corner and head regions:

Maximum height:width ratio permitted for projecting panel parts in corner or head regions resulting from support recesses in head regions. Each projecting part is checked separately. These parts must always be at right angles and parallel to the span direction.

If a projecting part does not meet these criteria, it is given the identifier for the illegal geometry element state. You then need to specify how to proceed (e.g. placing mandatory points, …).

'Recesses 2' tab

Recesses that are larger than the ones defined here can be created using steel headers. The recess width is also used to define the number of webs that are cut.

Recess in center of panel:

Maximum dimensions and minimum edge offset for recesses as shown below.

If the minimum edge offset is not complied with and the recess can be moved, the recess will be moved to the offset specified in the design process.
If a displacement is not allowed and the edge offset to the front is larger than the minimum offset specified for medium-sized recesses in the Recesses 1 tab, the program will issue a message during the design calculation process.
If a displacement is not allowed and the edge offsets are smaller than the minimum values specified for medium-sized recesses in the Recesses 1 tab, the program will create a recess in the corner, head or lateral area.

Lateral recess:

Maximum dimensions and minimum edge offset for recesses as shown below.

If the minimum edge offset is not complied with and the recess can be moved, the recess will be moved to the offset specified in the design process.
If a displacement is not allowed and the edge offset to the front is larger than the minimum offset specified for medium-sized recesses in the Recesses 1 tab, the program will issue a message during the design calculation process.
If a displacement is not allowed and the edge offset to the front is smaller than the minimum offset specified for medium-sized recesses in the Recesses 1 tab, the program will create a recess in the corner area.

'Hollow blocks' tab

Number, type and position of hollow blocks. You can define up to six areas.

Number:

Number of hollow blocks for the current area.

Type:

Selection box of the hollow block catalog.

x / y offset:

Axis spacing between hollow blocks and the panel edge or the axis of the last hollow block in the x direction as well as edge offset from hollow blocks to the bottom panel edge in the y direction for the current area.

'Insulation' tab

Type
Thickness / Material:

To apply insulation to the underside of the panel, enter the Thickness and select the insulation material you want to use in the Material list box.

Note: If the insulation material you need is not presented for selection, the thickness entered differs from the thickness specified for the relevant material in the insulation material catalog.
If the Define dimensions option is selected for the specified insulation material on the Placement tab, individual insulating boards are placed. Otherwise, one insulating board is created with the dimensions of the precast element.

End faces / Longitudinal sides

You can specify parameters for the concrete supports at the underside of the panel. You can make separate settings for end faces and longitudinal sides. The following variants are available: Not used, Concrete pads and Concrete beams. Depending on the variant selected, you can define the following parameters:

• Concrete pads for end faces: Assign a Fixture and select the Entry mode by opening the list box and clicking Below each web or Below specific webs. When you select Below specific webs, enter the Web numbers below which concrete pads are to be created. Use commas to separate the individual numbers (for example, 2,8,14).
  You can use the Offset to edge box to enter the offset from the reference point of the selected fixture to the panel edge.
• Concrete pads for longitudinal sides: Assign a Fixture and select the Entry mode by opening the list box and clicking one of the options provided. When you select the From center of panel edge on both sides option, you define the Offset between the concrete pads and the Minimum offset. For the other two options, you also need to specify the First offset of the first concrete pad from the relevant corner. All offsets are based on the reference points of the selected fixtures.
  You can use the Offset to edge box to enter the offset from the reference point of the selected fixture to the panel edge.
• Concrete beams for end faces and longitudinal sides: All you need to do is assign a Fixture.
  You can use the Offset to edge box to enter the offset from the reference point of the selected fixture to the panel edge.

Note: The numbers you enter for File no. and Entry must be the same as those in Allplan's fixture catalog.
The fixture you select for the Concrete pad must be a group fixture that consists of at least one linear fixture with the Interaction with precast element - Positive (merging) setting. This fixture is used to define the outline of the concrete pad in plan. The length of the defined linear component should be the same as the thickness defined for the associated insulating layer.
The fixture for the Concrete beam must be a linear fixture with the Interaction with precast element - Positive (merging) setting. This fixture is used to define the outline of the concrete pad in elevation.

'Recess' tab

End faces / Longitudinal sides

You can specify parameters for the recesses at the upper side of the panel. You can make separate settings for end faces and longitudinal sides. The following variants are available: Not used, Fixture and Parameters. Depending on the variant selected, you can define the following parameters:

• Fixture for end faces: Assign a symbol Fixture and select the Entry mode by opening the list box and clicking In each hollow block or In specific hollow blocks. When you select In specific hollow blocks, enter the Hollow block numbers where the recesses are to be created. Use commas to separate the individual numbers (for example, 2,8,14).
  You can use the Offset to edge box to enter the offset from the reference point of the selected fixture to the panel edge.
• Parameters for end faces: Specify the Length A and the Width B of the recess to be created. The other parameters are the same as those for the Fixture variant.
  
• Fixture for longitudinal sides: Assign a symbol Fixture and select the Entry mode by opening the list box and clicking one of the options provided. When you select the From center of panel edge on both sides option, you define the Offset between the recesses and the Minimum offset. For the other two options, you also need to specify the First offset of the first recess from the relevant corner. All offsets are based on the reference points of the selected fixtures.
  You can use the Offset to edge box to enter the offset from the reference point of the selected fixture to the panel edge.
• Parameters for longitudinal sides: Specify the Length A, Width B and Width C, Depth D and the Chamber (hollow block) where the recess is to be located. The other parameters are the same as those for the Fixture variant. However, you cannot specify an Offset to edge.
  

Note: The numbers you enter for File no. and Entry must be the same as those in Allplan's fixture catalog.

'->Fact.' tab

Assignment of the individual entries to the relevant factories.

The selected entry is applicable to the selected factories. If no factory is selected, the entry is valid for all the factories.