Table configuration entry

Configuration(s): edit element

'General table' tab

Text attributes:

Enter the attributes for the text in the table as follows:
H=..., W=..., A=..., F=..., P=..., C=...
The height and width of the text are entered in [mm] and the font angle in [degrees]. If you do not enter values, the defaults are used.

Maximum table length/ width:

Sets the limits for table size. If the table is too small for the list the program outputs an error at the end of the list (Table too small).

Include area of panel:

Includes the panel area in the table. Special customer-specific billing computation modes are not taken into account.

Include reinforcement type, panel thicknesses… etc.:

Enable the items that you want to be included in the table.

Include bar cross section:

You can choose between 'as required' or 'as present'.
The reinforcement quantity specified in the table of the edit element tool always represents the longitudinal bars, cross bars and the girders based on the enclosing rectangle of the element! In the case of panels and/or recesses of irregular geometry, individual longitudinal bars, cross bars and girders of the basic reinforcement may be excluded! This is ignored!

'Sequence' tab

Using this tab you can specify in which sequence the individual items of a panel are given in the table.

Every category has a numerical value, in other words a "start number", the higher the number the lower the priority. Enter 0 if the element is not to be listed.

The categories do not require any further explanation, except:

General:

This is the information enabled in the General table configuration entry.

Basic reinforcement list summarized:

Longitudinal or cross bars in an item, per layer, without lengths but with average bar spacing information
e.g. L: 16 d8/15

The reinforcement quantity specified in the table of the edit element tool always represents the longitudinal bars, cross bars and the girders based on the enclosing rectangle of the element! In the case of panels and/or recesses of irregular geometry, individual longitudinal bars, cross bars and girders of the basic reinforcement may be excluded! This is ignored!

Basic reinforcement list detailed:

Listing of the individual reinforcement items.

'List 1' tab

Basic reinforcement:

List's sort mode:

If the reinforcement list is enabled, you can sort it in various ways:

Dia_BS: bar diameter has the highest priority followed by bending shape.

Dia_Pos: bar diameter has the highest priority followed by the coordinates in the panel (from left to right)

Reinflay_Pos: the reinforcement is sorted first according to its layer (from the reinforcement type) followed by the coordinates in the panel (from left to right).

Reinflay_Length: the reinforcement is sorted first according to its layer (from the reinforcement type) followed by its length (shortest to longest).

Standard girders:

List's sort mode:

If standard girders are enabled, you can sort the list in various ways:

Typ_Pos: girder type has the highest priority followed by the coordinates in the panel (from left to right)

Pos_Length: the girders are sorted first according to position (from left to right) followed by length (shortest to longest).

Length_Typ: the girders are sorted first according to length (shortest to longest) followed by type.

Secondary bars:

Include arc bars:

Specify whether arc bars are to be included or not.

Width of a drawing as a number of characters:

Enter the number of characters available for the width of a drawing of a bending shape.

Height of a drawing as a number of characters:

Enter the number of characters available for the length of a drawing of a bending shape.

'List 2' tab

Bending shapes:

Number of columns for bending shapes:

Enter the number of columns for bending shapes you wish to be used in the table.

Width / height of a drawing as a number of characters:

Enter the number of characters available for the width/height of a drawing of a bending shape.

Show segment lengths:

When this option is enabled, the segment lengths of the bending shapes are displayed.

Stirrup shapes:

Beside stirrup cage/stirrup mesh:

Specify whether the stirrup shape is to be placed beside the stirrup cage/stirrup mesh or not.

Number of columns for stirrup shapes:

Enter the number of columns for stirrup shapes you wish to be used in the table.

Width / height of a drawing as a number of characters:

Enter the number of characters available for the width/height of a drawing of a stirrup shape.

Show segment lengths:

When this option is enabled, the segment lengths of the stirrup shapes are displayed.

Fixtures:

Include mark numbers:

Specify whether mark numbers are to be included or not.