|
|
|
Syntax
POINTS arg1 arg2
Description
Tendon points are created. First, the tendon points are created at the specified constraint points. These are dependent on the member and cross-section. After that, the transitions and constraints are determined.
Arguments
arg1
Value |
Meaning |
BEGIN |
Scope will be opened |
END |
Scope will be closed |
arg2 (arg1 = BEGIN)
Value |
Dimension |
Meaning |
ADD |
KEYWORD |
The content of the scope will be added to the list. |
CLEAR |
KEYWORD |
The list is deleted before the scope is imported. |
Scopes
TENDON
Examples
POINTS BEGIN
TPOINT 1 CGRID "MG-Box" s001 FRONT "Grid2(1:2)" INT
#TPOINT 2 CALC "" "" FRONT "" INT
TPOINT 3 CGRID "MG-Box" s002 FRONT "Grid2(1:2)" INT
TPOINT 4 CGRID "MG-Box" s003 FRONT "Grid2(1:2)" INT
TPOINT 5 CGRID "MG-Box" s004 FRONT "Grid2(1:2)" INT
TPOINT 6 CGRID "MG-Box" s005 FRONT "Grid2(1:2)" INT
TPOINT 7 CGRID "MG-Box" s006 FRONT "Grid2(1:2)" INT
TPOINT 8 CGRID "MG-Box" s007 FRONT "Grid2(1:2)" INT
TPOINT 9 CGRID "MG-Box" s008 FRONT "Grid2(1:2)" INT
TPOINT 10 CGRID "MG-Box" s009 FRONT "Grid2(1:2)" INT
TPOINT 11 CGRID "MG-Box" s010 FRONT "Grid2(1:2)" INT
TPOINT 12 CGRID "MG-Box" s011 FRONT "Grid2(1:2)" INT
TPOINT 13 CGRID "MG-Box" s012 FRONT "Grid2(1:2)" INT
TPOINT 14 CGRID "MG-Box" s013 FRONT "Grid2(1:2)" INT
#TPOINT 15 CALC "" "" FRONT "" INT
TPOINT 16 CGRID "MG-Box" s014 BACK "Grid2(1:2)" INT
TPOINT 1 SPLINE POS1 0.000 POS2 0.000
#TPOINT 2 SPLINE
TPOINT 3 SPLINE POS1 0.000 POS2 0.000
TPOINT 4 SPLINE POS1 0.000 POS2 0.000
TPOINT 5 SPLINE POS1 0.000 POS2 0.000
TPOINT 6 SPLINE POS1 0.000 POS2 0.000
TPOINT 7 SPLINE POS1 0.000 POS2 0.000
TPOINT 8 SPLINE POS1 0.000 POS2 0.000
TPOINT 9 SPLINE POS1 0.000 POS2 0.000
TPOINT 10 SPLINE POS1 0.000 POS2 0.000
TPOINT 11 SPLINE POS1 0.000 POS2 0.000
TPOINT 12 SPLINE POS1 0.000 POS2 0.000
TPOINT 13 SPLINE POS1 0.000 POS2 0.000
TPOINT 14 SPLINE POS1 0.000 POS2 0.000
#TPOINT 15 SPLINE
TPOINT 16 SPLINE POS1 0.000 POS2 0.000
POINTS END
The tendon contains 16 defined points with corresponding constraints. The start and end of the tendon are specified as straight line segments of length 1.0. This calculates the points 2 and 15 and outputs them here as comment lines.
|
(C) ALLPLAN GmbH |
Privacy policy |
